
Figure 1. A recessed stainless steel cover should sit flush with the surrounding paving, leaving only a controlled perimeter joint and minimal visible metal edge.
A stainless steel recessed manhole cover is not designed to draw attention. When it is installed correctly, it disappears into the paving pattern and leaves only a narrow, deliberate joint around the access point. When it is installed poorly, however, it becomes one of the first defects people notice: a proud edge, cracked tile, uneven grout line, trapped odour, or a cover that cannot be lifted after two winters.
The difference is rarely the cover alone. Even a well-made stainless steel access cover can fail if the frame is not fully supported, if the tray infill is too weak, or if the paving thickness has not been allowed for before ordering. This guide explains the installation process from a contractor’s point of view, with particular attention to load class, tray depth, bedding support and visual continuity.
Before site work begins, confirm three dimensions: the clear opening, the overall frame size and the usable tray depth. The clear opening is the size of the access chamber or structural opening below the cover. The overall frame size is larger because it includes the surrounding frame. Confusing these two measurements is one of the most common reasons for ordering the wrong product.

Figure 2. The clear opening, overall frame size and usable tray depth are different measurements. Each one affects product selection, excavation, paving cut-out and structural infill design.
The second check is the paving build-up. A recessed tray must hold the paving finish, adhesive or mortar bed, and a structural backing layer. For example, a 20 mm porcelain slab with a 6–10 mm adhesive bed does not mean a 30 mm tray is sufficient. There must still be enough depth for a stable concrete or mortar infill below the tile. In driveway and light commercial areas, shallow trays are more likely to suffer from tile debonding or cracking because the finished surface has less structural mass beneath it.
| Pre-installation item | What to verify | Why it matters |
| Clear opening | Chamber opening size, such as 600 × 600 mm | Determines whether the cover actually fits the access point |
| Overall frame size | External dimension of the complete frame | Needed for excavation and paving cut-out planning |
| Tray depth | Available depth for concrete, adhesive and paving | Prevents weak infill and tile cracking |
| Load class | A15, B125, C250 or higher depending on use | Prevents under-specification in trafficked areas |
| Seal type | Single seal, double seal or bolted/sealed design | Controls odour, water ingress and security requirements |
BS EN 124:2015 classifies access covers and gully tops by static test load and by the type of location where they are installed.1 A15 covers are intended for pedestrian and cyclist areas, while B125 is commonly used for footways, pedestrian areas and comparable areas such as car parks or domestic driveways. C250 applies to more demanding kerbside and slow-moving traffic areas, and D400 is used where cars and lorries have regular access.1

Figure 3. EN 124 classes are commonly discussed by static test load, but real site selection should also consider traffic speed, wheel position, turning forces and repeated loading.
| EN 124 class | Static test load | Typical application | Practical installation note |
| A15 | 15 kN | Pedestrian-only areas, gardens, patios | Do not use where cars may drive over the cover |
| B125 | 125 kN | Driveways, pedestrian zones with occasional vehicles | Bedding support and tray infill become more critical |
| C250 | 250 kN | Forecourts, kerbside areas, slow-moving commercial traffic | Use reinforced infill and check frame restraint carefully |
| D400 | 400 kN | Carriageways and areas with regular lorry access | Requires product-specific approval and installation guidance |
The load class should not be selected only by comparing it with the gross weight of a vehicle. Wheel position, turning forces, braking, tyre type and repeated loading all affect the real stress on the frame and tray. Mascot Engineering notes that speed of traffic, wheel type and the physical position of the cover should be assessed when choosing the right access cover.3 For any commercial project, the manufacturer’s test certification and installation method should be reviewed before installation.
“Under BS EN 124:2015, manhole covers, access covers and gully grates are graded by different loading applications, ranging from class A15 up to F900.” — JDP Pipes2
The cover frame must sit on a clean, level and structurally sound base. Remove loose mortar, broken brickwork, dust, oil and standing water from the top of the chamber. If the chamber is below finished level, build it up with engineering brick or suitable concrete so that the cover frame can be fully bedded at the correct height.
A stainless steel frame should not be used to bridge a weak or uneven chamber. If the frame is supported only at the corners, the load path becomes concentrated and the cover may rock, settle or crack the surrounding paving. The aim is to create a continuous bearing surface beneath the entire frame, not a few isolated contact points.
Apply a continuous bed of high-strength, non-shrink or polymer-modified mortar around the chamber. For pedestrian areas, a 10–15 mm bedding layer may be adequate, but trafficked areas generally require a deeper and more robust bed. The exact bedding material should follow the cover manufacturer’s instructions and the project specification.
Place the frame into the mortar and level it carefully to the finished paving height. A laser level is preferable on large-format porcelain or stone paving because even a small height error becomes visible across a flat surface. Press the mortar around the frame flange so that the frame is restrained laterally as well as vertically. This is particularly important on driveways, where steering movement can apply horizontal forces to the edge of the cover.
The tray is not simply a decorative holder for paving. It is the structural core of the recessed cover. For external paving, especially where vehicles may pass over the cover, the lower part of the tray should be filled with a suitable concrete or high-strength mortar backing. The depth left above this backing must match the adhesive bed and the final paving material.

Figure 4. A correct installation creates a continuous load path from paving finish to tray, frame, full mortar bed and sound chamber wall.
A bonding slurry or suitable primer can be applied to improve adhesion between stainless steel and the infill, subject to the manufacturer’s recommendation. This is especially useful where vibration, thermal movement or repeated loading may otherwise cause debonding. If the infill separates from the tray, the paving above may sound hollow, crack at the corners or loosen over time.
The visual success of a hidden manhole cover is decided before the adhesive is mixed. Dry-lay the paving pieces inside the tray and check that the grain, grout lines and tile cuts continue across the cover. On stone-effect porcelain, the off-cut from the surrounding paving should often be placed inside the tray to preserve the direction of the vein.

Figure 5. Consistent grout lines and aligned tile veins help the access cover read as part of the paving, rather than as a separate object.
The joint around the tray should look intentional. If the surrounding grout joints are 5 mm, the perimeter joint around the cover should not suddenly become 12 mm on one side and 2 mm on another. Consistency is more important than trying to make the joint disappear completely. A clean and regular joint reads as part of the paving design; an irregular joint immediately reveals the access point.
After the paving has been fixed, grout the tray using a suitable weather-resistant grout or flexible sealant, depending on the finish and expected movement. Before closing the cover, clean the lifting points and gasket channel. Mortar dust or grit on an EPDM gasket can prevent proper sealing and may cause odour leakage in drainage applications.
Do not load the cover too early. Light foot traffic should normally be avoided for at least 24 hours, and vehicular loading should be prevented until the bedding and infill have reached sufficient strength. On driveways and commercial areas, premature loading is a common cause of frame settlement and edge cracking.
| Failure | Likely cause | How to prevent it |
| Frame rocks under load | Spot bedding or uneven chamber surface | Use a full continuous mortar bed and level the support surface |
| Tile cracks inside tray | Weak infill, shallow tray or poor bonding | Use structural backing and allow adequate depth below paving |
| Cover is difficult to lift | Grout or debris in lifting points | Clean threads and lifting sockets before final handover |
| Odour escapes from chamber | Dirty or damaged gasket, poor seal contact | Clean the seal channel and check gasket compression |
| Cover remains visually obvious | Misaligned grout lines or inconsistent perimeter gap | Dry-lay first and match cuts to the surrounding paving |
Before handover, check that the cover sits flush with the surrounding surface, the frame is stable under load, the paving pattern aligns across the tray, the lifting keys fit correctly, and the gasket is clean. If the cover is installed in a trafficked area, record the load class and keep the manufacturer’s installation guidance with the project documents. This is useful not only for quality assurance but also for future maintenance.
A recessed stainless steel manhole cover should be specified and installed as a small structural component, not as a cosmetic accessory. When the clear opening, load class, tray depth, bedding method and paving layout are coordinated from the beginning, the result is a safe access point that remains discreet, serviceable and visually consistent with the surrounding floor.
[1] Wrekin Products: Understanding BS EN 124 groups and classes
[2] JDP Pipes: What is the BS EN 124 classification?
[3] Mascot Engineering: BS EN 124-2
Contact: Chris
Phone: + 86 16624782481
info@manholecoversupply.com
Add: Room B0456, 8th Floor, No. 88 Tangjing Road, Baiyun District, Guangzhou